技術參數 Technical Parameters
【產品詳情圖片】
容 器 類 別 Tank Type：Ⅱ類
介質 Medium：LCO2
設 計 壓 力 Design Pressure: 2.2MPa
允許工作壓力Max. Allowance working pressure: 2.27MPa
容 積 Volume ：10.5m3
材料Materials：
內膽Liner：16MnDR
外膽 Shell：Q345R
規格Specifications：
內膽 Liner：φ1600×8/8
外膽 Shell：φ2100×8/8
總重 Weight：7600kg
夾層保溫材料Sandwich insulation material:
CEP60型珠光砂（含水量≤0.3%） CEP60 pearl sand (water content ≤0.3%)
內膽氣壓試驗 Liner pressure test：
介質 Medium：氮氣 Nitrogen 試驗壓力 test pressure：2.61MPa
內膽內管材料Liner tube materials：S30408
閥門 Valve：低溫不銹鋼三段式球閥 cryogenic stainless steel three stage ball valve
制造驗收標準 manufacturing accept standards：
According to GB/T 18442-2011 Stationary vacuum insulated cryogenic pressure vessel
TSG 21-2016 Safety technical supervision procedures for fixed pressure vessels
【產品詳情圖片】
【變量3】【變量2】【變量1】

液體的儲存 liquid storage
液體二氧化碳的儲存屬于帶壓（壓力不低于0.8Mpa）儲存。儲存期間除壓力表、液位計、安全閥應投入使用外，其他閥門應處于關閉狀態。當儲罐壓力超過2.1Mpa時，開啟V7排氣閥降壓。但應注意：內罐的壓力不得降至低于0.8Mpa，否則將引起液體二氧化碳轉變?yōu)楦杀?br>Liquid carbon dioxide storage with pressure (pressure not less than 0.8Mpa) storage. During the storage, the pressure gauge,level gauge, safety valve should be put into use, the other valves should be closed. When the tank pressure exceeds 2.1Mpa, open the V7 exhaust valve buck. However, it should be noted that the pressure inside the tank must not drop below 0.8Mpa, otherwise liquid carbon dioxide will be converted to dry ice.
【產品詳情圖片】
【標題】

維護與檢修 Maintenance and repair
【產品詳情圖片】
1.儲罐的使用與維護，應按“壓力容器安全技術監察規程”要求和本說明進行。
The use and maintenance of the storage tank shall be carried out according to the requirements of the Pressure Vessel Safety Technical Supervision Regulations and these instructions
2.日常檢查與維護 Daily inspection and maintenance
儲罐在運行過程中，要經常檢查安全閥、壓力表、液位計工作是否正常，閥門管路是否有泄漏，外部有無異?，F(xiàn)象，發現問題及時處理。
During operation of the tank, check the safety valve, pressure gauge and liquid level meter regularly, whether the valve line is leaking, whether there is any abnormal phenomenon outside, and find the problem to be handled in time.
3.定期校驗 Regular verification
3.1安全閥整定壓力不大于2.27Mpa，每年至少校驗一次，并加鉛封，作好記錄。
Safety valve setting pressure is not more than 2.27Mpa, at least once a year, and add seals, make a record.
3.2定期檢查夾層真空度，未裝低溫介質的情況下真空度應低于65Pa，裝有低溫介質的情況下，真空度應低于10Pa為合格。
Regularly check the sandwich vacuum, the vacuum should be less then 65Pa without vacuum medium; with a low temperature medium, the vacuum should be less than 10Pa for the pass.
【產品詳情圖片】
【標題】

【標題】
【變量2】【變量1】
【產品詳情圖片】
山東中杰特種裝備股份有限公司是國內知名的低溫儲罐生產廠家，具有A1，A2壓力容器設計、制造許可證，專業從事液氧LO2、液氮LN2、液氬LAr、液態LCO2及液化天燃氣（LNG）等低溫液體貯罐、大型常壓貯罐和Ⅰ、Ⅱ、Ⅲ類非標壓力容器設備、化工設備，產品廣泛用于制藥、石油化工、有機合成、冶金、食品、醫療、生物工程、國防等行業。三十幾年來，企業規模不斷發展壯大，現擁有固定資產3.5億元，生產廠區3個，具有先進的加工設備和完善的檢測設備，公司現有職工800余人，年銷售4億多元，并把低溫壓力儲罐作為公司爆品打造。
【產品詳情圖片】

http://m.7qe.net